Jigsaw lubrication

[esimkins]

I am looking for information on how to lubricate my jigsaw. I don't have a manual, but looks simple enough. Looks like the one below here: http://www.shopsmith.com/ownersite/faq/jigsaw.htm. This jigsaw looks like it hasn't been used for the last ten years or so. I have lubed the top spring loaded shaft and cleaned the dust and sawdust out of the bottom part that clamps onto the blade. Now it works great, but serial shows it is a 1959 model, so I would like to know it is getting the proper lubrication before continuing to use it.

I have opened up the cover below and above the blade, but that didn't tell me what to oil it with? Maybe a spray on oil?

Anyone know what Shopsmith recommends?

Thank you,

Eric

[SDSSmith]

The manual says "Use a good quality, light 10W machine oil, such as sewing machine oil. You can purchase this oil at most hardware stores, sewing centers, or automotive stores. Avoid penetrating oils and oils with detergent additive."

That being said, I know of folks that have used a non-detergent 20W and 30W oil down here in SoCal.

[solicitr]

The most inportant part is to lubricate the crankcase. The oil probably should be changed at that age. Take off the serial number plate und you'll see a large slothead screw. Find a small container, remove the screw, and lay the whole unit over on its side so as to drain the oil. Now set it up level (on the mounting is fine), and fill up the reservoir until the oil is flush with the bottom of the hole. Reassemble.

Also lube the airpump seal: take off the top cover and put just a couple of drops on the inside of the hoolw shaft.

[esimkins]

Thank you Rob, I should be able to locate the oil, I will try at ACE first. Now how about where to lube it? Should I just open the door at the bottom of the unit and squirt some in and around? And the top? Just open it up and squirt some down into the hole that holds the spring? Or just lube the shaft part that holds the top of the blade?

I am also in SoCal, but would think the 10W should be better than the other weights.

Is that Mini Mark the one in your picture? Did you make that? or did they sell something like that?

Thanks again,

Eric

[esimkins]

The most inportant part is to lubricate the crankcase. The oil probably should be changed at that age. Take off the serial number plate und you'll see a large slothead screw. Find a small container, remove the screw, and lay the whole unit over on its side so as to drain the oil. Now set it up level (on the mounting is fine), and fill up the reservoir until the oil is flush with the bottom of the hole. Reassemble.

Also lube the airpump seal: take off the top cover and put just a couple of drops on the inside of the hoolw shaft.


Thank you Bill, I should have waited on my second question, you have just answered it. I had only peeked into the top and bottom, I hadn't looked behind the serial plate, I will have to give that a try. I would have thought the crankcase was behind the plate with the "M" in the front. Inside there looks like the crankcase of a car engine, and it was dry, very clean, but dry or at least clean with no oil.

Thanks both Rob and Bill, I will let you know what I find in the next day or two.

Eric

[solicitr]

I would have thought the crankcase was behind the plate with the "M" in the front. Inside there looks like the crankcase of a car engine, and it was dry, very clean, but dry or at least clean with no oil.


Eric

Yep, the crankcase is behind the M plate- but you don't want to remove that to fill it any more than you want to drop your car's oil pan to change the oil!

[rcoder]

I have used transmission fluid in mine for years. Works great. Be sure to clear the air hole with a fine wire. That lets the air pressure equalize with each revolution. It helps keep the oil in the crankcase.

Bob

[SDSSmith]

Is that Mini Mark the one in your picture? Did you make that? or did they sell something like that?

That is a Mini that I made.....works great as a power station. Take care and good luck with that jigsaw.