510 Router Table Ideas

[jgrounds]

http://members.cavtel.net/jgrounds/rt3.jpg

Additional ideas in pictures at http://www.firechat.com/RT.HTM. Please note the comments section at the end of this link will not work properly (Old html coding) If you have comments leave them here:) .

John

[dusty]

Excellent job, John.

I would be interested in seeing some detail about how you attached the rails to the table. It looks as though they are attached to an aluminum bar which is in turned lagged to the table.

I am curious about why you have the router setting at an angle.

Is the table made from MDF or is it phenolic?

Excellent Job!

[judaspre1982]

Nice set up. My guess is if the router mounting plate is set square to the table, the router handles on the router will hit thw way tubes. Just a guess.------Dave

[jgrounds]

Excellent job, John.

I would be interested in seeing some detail about how you attached the rails to the table. It looks as though they are attached to an aluminum bar which is in turned lagged to the table.

You are correct. The aluminumbar is attached by screws to the table.


I am curious about why you have the router setting at an angle.

and,

Judaspre1982
My guess is if the router mounting plate is set square to the table, the router handles on the router will hit thw way tubes.

That is the way it fit the best for me. The insert was pre drilled for my router and I tried to get the best fit for the router between the ways.


Is the table made from MDF or is it phenolic?

Got the table at Woodpeckers on clearance. It is 1 1/8 inch thick including the top and bottom surfaces. The mid section looks like a form of MDF.


John

[dusty]

Thanks John for the feedback. Your table looks great and seems to have evolved out of a lot of thoughtful analysis of your needs.

I was interested in how you attached the rails to the MDF mostly because I have a small accumulation of 510 rail parts. I am looking for ways to utilize these. I posted an approach that sort of worked but yours seems much better.

Hopefully this will give someone an idea on how they might repurpose their harvested parts.

[gilamonster]

John - I'm looking at the pictures of your excellent router-table ShopSmith addition.

My question is: how easy/difficult is changing bits and height adjustment. Is there very much access room under there, with the waytubes, etc.?

(edited to correct my lack of reading comprehension <G>)

[Ed in Tampa]

John - I'm looking at the pictures of your excellent router-table ShopSmith addition.

My question is: how easy/difficult is changing bits and height adjustment. Is there very much access room under there, with the waytubes, etc.?

(edited to correct my lack of reading comprehension <G>)

I'm not John but let me make a suggestion. If you ever watch Router Workshop on PBS they merely lift the whole router/plate and make any adjustment.
I know people like the idea of doing under table adjustments but frankly I find being able to set the whole thing on edge and making the height adjust exactly where I want it is really beneficial. Since the plate stays attached it is easy to measure or use brass set blocks to get exactly what you want.

For changing bits again I don't do well hunched over trying to manever a couple of wrenches or push a spindle lock and using one wrench very well. I like having the whole thing at work level an as visible as possible.

With John's setup you can simply lift the router/plate up and set it on it's side on the router table and make any adjustment or bit change you want. Then just drop the router/plate back in place and your are ready to go.

[jgrounds]

I'm not John but let me make a suggestion. If you ever watch Router Workshop on PBS they merely lift the whole router/plate and make any adjustment.
I know people like the idea of doing under table adjustments but frankly I find being able to set the whole thing on edge and making the height adjust exactly where I want it is really beneficial. Since the plate stays attached it is easy to measure or use brass set blocks to get exactly what you want.

For changing bits again I don't do well hunched over trying to manever a couple of wrenches or push a spindle lock and using one wrench very well. I like having the whole thing at work level an as visible as possible.

With John's setup you can simply lift the router/plate up and set it on it's side on the router table and make any adjustment or bit change you want. Then just drop the router/plate back in place and your are ready to go.

Great answere Ed!

John