10ER in pictures, lite on the review

[reible]

Hi,

As some of you may know I have a Shopsmith 10ER I just got. It is the first one I have seen up close and personal... touching and hefting as well. I will be giving this one to my brother as a birthday gift but if I EVER have space I'll get one for myself too.

I'm really having trouble not digging and and working on it but then part of the gift well be for him to do that so... But I did power it up to make sure it at least ran. I also decided to check the bearings. While they feel tight and I don't think they are damaged they also feel stiff like they are running in 58 year old grease. Not sure what I want to do about that. In the pictures you will see I have both the quill and pulley side bearings out. When I get it back together I might add a picture with them just for completeness.

This well be several posts due to the 5 limit of images per posting. I may not do them all today as it takes a while but I think some of you are going to find this very interesting in light of some discussions in the past.

So off we go with an image of the hole where the quill should be. As you can see it looks a lot like the current design as far as the gear system.
3614

Next is the other end where the bearings set that are for the drive portion of the machine. A little later I have a picture of what the missing piece looks like but for now think of it as a pair of bearings with a pulley attached to a shaft.
3615

Check out the tubes on this beauty... makes you want to go park a Buick on them. They look to be just short of a 1/4" tube thickness. This is the end that goes in the air when setting up in drill press mode, the tubes come though the tie bar and a threaded knob is used rather then the latch idea of the newer models.
3616

Yes the pulley is the drive and yes it is exposed on the lower end. As you can see you need to move the belt from pulley to pulley to change speed. This was the stock setup but they had a speed changer you could add... this machine didn't have that option.
3617

The lever is the quill lock. The quill spring I haven't had apart so I can't tell you how that works but in general it is about the same in function.
3618

Ed

[reible]

Hi,

Next you can see the headstock lock. I like the feel of the levers, the pictures don't let you feel them but they have a nice smooth flow to them.
3619


This is the knob that holds the top pulley guard in place. This machine is missing that part but I really want to get one as soon as I can... it didn't worry me to much in this position but when in drill press mode it could be a hair pulling experience. And yes even in the horizontal mode it feels a little unsafe.
3620

Just like on the current machines you can move the lever to either side.
3621


Next we have the quill and the drive pulley assembly. Not much more I can say about them.
3622


A little longer shot at the head stock. As you can see the motor mounts below and has a pair of tubes that are used to adjust the belt tension. To tight you wreak the bearings and too loose and the belt hits the tubes. Yes the belt goes between the tubes so you are limit as to the size of pulley's you can use.
3623


Ed

[reible]

Hi, are you still here?

Please note the crank under the carriage, you will see more of that and what it is for a bit later.
3629

Notice the pivot point and how they have the off set. You can also see the knob for locking it in that position.
3630

This a good shot showing the carriage lock and the table height locks, and a better view of the drill press lock position lock.
3631

Here is a shot giving more of a prospective from the end.
3632

Take a look at the cord, mice or from the exposed pulley... up and it person you can tell it was from the pulley. That could make a mess of a pulley and anyone near the shower of metal... could even cause a fire with all the sawdust around.
3633

Still more to come.

Ed

[reible]

Hey who needs a ground when you can have a homemade chipboard piece on your power cord??? Original??
3634

The next collection is of the main table. Take a look at how some of the stuff was done back then, especially the 90 and 45 degree lock positions.
3635
3636
3637

Another picture of the crank, this time from above. Also note the part of the height adjuster in the last couple of pictures.

3638

Wonder what will be in the next batch of picture in the next post???

Ed

[reible]

What is up next is how the crank and the top all come together. Interesting design hey?
3639

The miter gauge. A bit different then today's but interesting all the same.
3640

The next time is the extension table of that day. First a couple shots of it from the sides and then a shot of it mounted on the machine.
3641
3642
3643

Ed

[reible]

We are getting near then end...

Another view showing the main table and extension table. Almost looks like a shopsmith doesn't it?
3644

The saw guard. As I understand it they never did make a bottom part for it. This one I don't think got much use.
3645

The 12 sanding disk and a smaller one, I think it is 8" but I never did measure it to be sure. I think the smaller one is from shopsmith but I am really not sure as the design is very different.
3646

And to round out this post the lathe tool rest.
3647


Now for a shocking revelation check the next posting.

[easterngray]

Thanks Ed - Thats the most in depth look I've had at one of those machines. Can you confirm that the tube dimensions are the same as the Mark V tubes? I would love to have heavier bench tubes on my Goldie. Thanks again. Alec

[kartoffelkopf]

Thanks Ed - Thats the most in depth look I've had at one of those machines. Can you confirm that the tube dimensions are the same as the Mark V tubes? I would love to have heavier bench tubes on my Goldie. Thanks again. Alec

Sorry, they are not.