Making a Router Table that fits on my 510

[THOMRIDER]

anyone tried making a router table to work on you shopsmith 510 or other shopsmiths. looking for ideas of how to do it

[curiousgeorge]

This might give you some ideas... SawTrain Systems (http://jointech.com/shopsmith500&510.htm)

[dusty]

anyone tried making a router table to work on you shopsmith 510 or other shopsmiths. looking for ideas of how to do it

Are you thinking about a router that simply resides on the Mark. If you are thinking of the later, I would give up on that thought immediately due to speed deficiency.

If you are thinking of mounting a router table (with router) on that Mark V that is doable. I would think along the lines of one of the following:

Pro Fence Router Table System (555865)

http://www.shopsmith.com/ownersite/itemfind.htm?item=555865&Submit=Find+Item

OR

Router Table Kit (555658)

http://www.shopsmith.com/ownersite/itemfind.htm?item=555658&Submit=Find+Item

Either approach could be built and assembled by anyone but would best be done (most easily be done) after buying some select parts from Shopsmith. Might be more work than worth.

I have both and find them each useful in their own ways. If I had to select one over the other I would chose the 555865.

[a1gutterman]

anyone tried making a router table to work on you shopsmith 510 or other shopsmiths. looking for ideas of how to do itWelcome, THOMRIDER,
If making one yourself, you might have a look at the picture of the one that SS sells (http://www.shopsmith.com/ownersite/itemfind.htm?item=555658&Submit=Find+Item). SS also makes a router table that is included with the Incra Ultimate Fence/Router System Package (http://www.shopsmith.com/ownersite/itemfind.htm?item=555935A&Submit=Find+Item)for the 510. This table has rails for the 5' tubes and does knot seem to be available separately (item #522155, which does knot come up as a good item number). The member that, today, started another thread (http://www.shopsmith.net/forums/showthread.htm?t=4894), might be interested in talking to you about their table. That member might want to buy a different table (http://www.shopsmith.com/ownersite/itemfind.htm?item=555865&Submit=Find+Item)that will fit their 520 table system. Hope this has helped you.

The item #555865 (http://www.shopsmith.com/ownersite/itemfind.htm?item=555865&Submit=Find+Item) fits the 520 table system and will knot work on the 510 table system. The 555865 is the table that camilleraven needs, and camilleraven has the table that wood work for you, the 522155.

In order for the 555865 to work for you, you will need to upgrade your table system to 520.

[dwevans]

I purchased a Rockler router table top, and added some 510 rails on angle iron underneath to help hold it in place on the shopsmith. Now when I need to use my router table, I set the lefthand extention table to the same height as the main table, place the router table top on the extension table and main table, run the 2' tubes through the rails and tighten them down. Makes a very stable and inexpensive router table for a small shop. When I'm not using the table, I can lean it against the wall where it takes up little space.

Sorry, I have no pictures at the moment, I'll see if I can post them later.

[jgrounds]

http://www.shopsmith.net/forums/showthread.htm?t=2753&highlight=router

John

[THOMRIDER]

man thanks for the link I want to make that exact table, I will have to find some 510 tubing somewhere for cheap if possible so it will work the way I want.

[a1gutterman]

man thanks for the link I want to make that exact table, I will have to find some 510 tubing somewhere for cheap if possible so it will work the way I want.FYI, the router table that I received from ShopSmith with my Incra Ultimate package (for model 510 table system), is exactly like that, except the placement of the router plate is in the center of the table.