View Full Version : Re-installing motor
marshoaks
03-23-2010, 07:38 AM
I'm brand new to the forum. I've inherited a ShopSmith from my son who transferred from a project and left it with me. Before he left one of the sheaves (sp??) was broken, so he said. I cannot see that either of them are broken. I tried to reinstall the motor so I could run it and try and see what the problem is. However, I can't even fit the motor and it's cover beyond the horizontal tubes.
Sorry, I don't even know what model I have. Can someone tell me how to determine the model and how to reinstall the motor.
Thanks in advance.
Marshoaks
thainglo
03-23-2010, 08:01 AM
Pictures? Will help the group diagnose your issue a lot better than guessing from what you've written.
dusty
03-23-2010, 10:11 AM
I'm brand new to the forum. I've inherited a ShopSmith from my son who transferred from a project and left it with me. Before he left one of the sheaves (sp??) was broken, so he said. I cannot see that either of them are broken. I tried to reinstall the motor so I could run it and try and see what the problem is. However, I can't even fit the motor and it's cover beyond the horizontal tubes.
Sorry, I don't even know what model I have. Can someone tell me how to determine the model and how to reinstall the motor.
Thanks in advance.
MarshoaksAs already stated, we need a bit more information to be able to help. If you can find any markings (on the headstock) that would identify the unit we would be better off. Model number, part number, serial number - anything. Pictures would also help.
In the meantime, the motor is mounted with four bolts inside the motor pan. The motor pan mounts to the headstock with four or five screws.
Maybe these will help:
http://www.shopsmithacademy.com/SS_Archives/SS121/SS121_Shopsmith_Reborn_Pt1.htm
http://www.shopsmithacademy.com/SS_Archives/SS121/SS121_Shopsmith_Reborn_Pt1.htm
JPG40504
03-23-2010, 04:43 PM
As already stated, we need a bit more information to be able to help. If you can find any markings (on the headstock) that would identify the unit we would be better off. Model number, part number, serial number - anything. Pictures would also help.
In the meantime, the motor is mounted with four bolts inside the motor pan. The motor pan mounts to the headstock with four or five screws.
Maybe these will help:
http://www.shopsmithacademy.com/SS_Archives/SS121/SS121_Shopsmith_Reborn_Pt1.htm
http://www.shopsmithacademy.com/SS_Archives/SS121/SS121_Shopsmith_Reborn_Pt1.htm
If it has adjustable sheaves, then it is a Mark 5 or a Mark V"(possibly a mark 7, but not likely).
As Dusty has stated, the motor mounts by 4 screws to the 'motor pan'. Realize that that mounting is done with the motor pan removed from the headstock. The motor pan/motor/linecord are then mounted to the headstock by 5 very small screws. This is easier done with the headstock raised to the vertical(drill press) position. Position the headstock all the way to the right(bottomed out in vertical mode).
However the sheaves can be examined without the motor 'running'(indeed such is not to be recommended if a sheave is broken).
With the motor pan removed it is quite easy to visually examine the control sheave etc.
What we do not know here is what is meant by 'broken'. A chunk physically broken off. It doesn't work properly.
The links from Dusty above should help you understand how it is put together, and how it should work.
heathicus
03-23-2010, 04:45 PM
Shouldn't just a removal of the belt cover give visual access to the sheaves?
JPG40504
03-23-2010, 04:48 PM
Shouldn't just a removal of the belt cover give visual access to the sheaves?
He should be looking at them if the motor is 'removed'.
That said, realize there are two variable sheaves. One is the motor pulley, and the other is the idler shaft pulley.
Also the 'belt cover' must be removed to attach the motor pan etc.
hobbydad
03-24-2010, 11:52 AM
Marshoaks,
When I need to remove/reinstall the motor pan, I use this method:
Put the SS in horizontal mode
Raise the main table so the bottom of the vertical tubes is above the base tubes
Put a board across the base tubes underneath the vertical tubes of the main table
Unlock the handle for changing to vertical mode
Crank the main table down until the way tubes begin to raise
You should be able to raise the headstock enough to slide the motor pan underneath, then lower it back down to attach it.
If this isn't clear, I can try to take a picture.
Loren
marshoaks
03-25-2010, 06:20 AM
Thanks to all for the helpful suggestions. I knew so little that I wasn't even aware that the top tubes could be raised to the vertical position. I'm learning though.
I removed the sheaves from the motor with my son's assistance and found that the noise was coming from the sheave being too close to the motor housing. I tightened the set-screw and the noise is gone. Not sure if that is what my other son thought was the problem or not. I will reassemble and see what happens.
Again, thanks to all and I'm sure I'll be seeking your advice again.
Marshoaks